In the salon

Hair removal room setup: layout, power, light and a checklist

Checked · 6 min read

In short

What do you need to set up a hair removal room?

A separate room with space to work on both sides of the couch, a stable power supply, even light, eye protection, hygiene supplies and a place to keep client records. The device sets some of the requirements: ask the supplier in writing what it needs. For iPRO MINI, this is distilled water and a voltage stabiliser rated from 3 kW, and the first launch is done by a service centre engineer or remotely, following a video guide. Plan the layout around the specialist: the couch reachable from both sides, the device on the side of the working hand, the cables out of the walkway. Keep one place with the same light for before and after photos. Requirements for premises differ by country and region: check them where you work before you fit out the room.

iPRO MINI: first launch, maintenance and service

A hair removal room is set up once and then works for years. Mistakes made at the start, such as a socket in the wrong place or poor light, cost minutes with every client. This checklist covers what is the same in most countries. Local requirements for premises are not retold here: check them where you work.

Space and layout

  • A separate room that closes: the client undresses, and the treatment needs calm and privacy.
  • Space on both sides of the couch, so that the specialist can reach every area without stretching or moving the client.
  • A couch with adjustable height and backrest: areas from the face to the legs need different positions.
  • The device on the side of the specialist’s working hand, with the handpiece holder within reach.
  • The handpiece cable and the power cable out of the walkway.

Every minute the layout saves is repeated with every client.

Power supply

A professional device needs a stable supply. Ask the supplier in writing what the device requires and whether a stabiliser is needed. For iPRO MINI, you need distilled water and a voltage stabiliser rated from 3 kW; everything else comes with the device. Plan a socket close to the device for it alone, and ask an electrician to check that it is properly earthed and suitable for the load.

The first launch of iPRO MINI is done by a service centre engineer, or remotely by the salon, following a video guide. What else is needed is described on the service page.

Light, temperature and air

  • Even, bright light for assessing the skin and hair before each area.
  • A comfortable room temperature: the client lies partly undressed.
  • Fresh air between clients.
  • Blinds on the windows for privacy, and no direct sunlight on the couch.

Eye protection

Bright flashes call for eye protection for the specialist and the client. Ask the supplier which protection matches the wavelength range of each handpiece and what comes with the device. The ranges for iPRO MINI are 755–1064 nm for the IPLASER 755 handpiece and 560–1064 nm for the IPLASER 560. Keep the protection next to the device, so that no session starts without it.

Hygiene and supplies

  • Cleaning between clients: the handpiece window and the parts that touch the skin, as the device manual says.
  • Disposable couch covers, wipes and a disinfectant suitable for the device surfaces.
  • Gel, if the device needs it, and a place to wipe it off. With contact cooling, as on iPRO MINI, there is no ultrasound gel to store or apply.
  • Distilled water for the device: on iPRO MINI the salon changes it once a month.

The full maintenance calendar is in the article IPL machine maintenance.

Records and photos

Each client has a form with health questions, contraindications, the skin type, the settings used and the dates of the course. Keep it where only staff can reach it, on paper or in software, and follow the data protection rules where you work. For before and after photos, choose one place in the room with the same light and background, and take photos only with the client’s written consent.

What the form records is described in the article consultation and contraindications.

One room for two services

A room pays back faster when it has more than one service. On iPRO MINI DUO, the IPLASER 755 handpiece for hair removal and the IPLASER 560 for phototherapy swap on the same device, so both treatments share one room and one client base. How this enters the calculation is shown in the article is hair removal profitable.

Checklist before the first client

  1. Check the local requirements. What the premises need, and whether registration or notification is required where you work.
  2. Check the power. A properly earthed socket for the device alone and, if the supplier requires it, a stabiliser.
  3. Launch the device. With a service engineer or by the supplier’s video guide, with distilled water ready if the device uses it.
  4. Set out the eye protection. For the specialist and the client, matching the wavelength range.
  5. Prepare the forms. The client form, the consent to treatment and the consent to photos.
  6. Train the specialist. On the device, the protocols by area and skin type, and contraindications.
  7. Do a trial run. Go through a full visit without a client, from the consultation to cleaning the handpiece.

Questions and answers

What equipment does a hair removal room need?

A couch with adjustable height, the device, a stable power supply, even light, eye protection, hygiene supplies and a place for client records.

What does the power supply need?

It depends on the device: ask the supplier in writing. For iPRO MINI, a voltage stabiliser rated from 3 kW and distilled water are needed.

How big should a hair removal room be?

Big enough to work on both sides of the couch and to keep the cables out of the walkway. Minimum sizes, where they exist, are set by local rules: check them where you work.

Is eye protection needed for IPL?

Yes, for the specialist and the client. Ask the supplier which protection matches the wavelength range of each handpiece.

Can one room be used for hair removal and skin treatments?

Yes, if the device does both. On iPRO MINI DUO, the hair removal and phototherapy handpieces swap on the same device.

This material is for reference only and is not legal or technical advice. Requirements for premises, electrical installations and client data differ by country and region: check them with the authorities and professionals where you work. Checked on 17 November 2026.

Request

Did not find your answer?

Write your question and an Innovatione specialist will reply.

Innovatione stand at an industry exhibition, with visitors at the stand

Innovatione stand at an industry exhibition

What do you need?